Spring-can hangers support piping while allowing movement as temperatures and loads change. During a hydrostatic test, they remain part of the installed support system and need no special adjustment. Learn how pipe supports relate to pressure testing and why changing them can affect the pipe’s behavior.

Multiple Choice

What preparation must be made for the Spring-Can hangers of a section of a pipe before hydro testing can be performed?

Hydro testing checks the pipe and its joints for leaks and strength under the test pressure, using the system in its installed condition. Spring-can hangers are flexible supports that carry the pipe and allow movement during pressure changes, so they don’t affect the containment path or leak checks. Because of that, no special preparation of the hangers is needed before the test. Altering hangers—like tightening bolts, removing supports, or adding insulation specifically for the test—could change how the pipe is supported and influence test results, so they aren’t required.

Hydrostatic testing puts a piping system under pressure to check its strength and reveal leaks. The pipe is filled with liquid—usually water—and pressurized according to an approved procedure. For a section supported by spring-can hangers, the hangers generally need no special preparation before the test. They remain in place as part of the installed support system.

That may sound like a small detail, but it reflects a larger principle in boiler and piping work: test the system in a condition that represents how it is meant to function, unless the test plan says otherwise. A support that carries pipe weight and allows movement is part of that system. Changing it without a clear reason can create problems rather than solve them.

What a spring-can hanger does

A spring-can hanger supports a pipe while allowing it to move vertically as operating conditions change. When hot fluid passes through a line, the pipe expands. When it cools, the pipe contracts. The spring inside the hanger responds to that movement, helping support the pipe without pinning it rigidly in place.

Think of it like a cushion beneath a moving load. It carries weight, but it also gives the pipe room to shift as temperatures and loads change. That flexibility matters in steam systems, boiler piping, and other lines where heat can cause noticeable movement.

A spring-can hanger is not part of the pipe’s pressure boundary. The pressure boundary is formed by the pipe, fittings, welds, flanges, valves, and other components that contain the fluid. The hanger supports the outside of the line; it doesn’t seal the fluid inside it. So, as a general rule, the hanger itself doesn’t need to be tightened, removed, or insulated to make a hydrostatic test meaningful.

Why the hangers stay as they are

A hydrostatic test checks the piping while it’s filled and pressurized. That changes the load on the system: water is much heavier than air or steam, and the weight of the filled pipe must be carried by its supports. Leaving the spring cans in their intended positions helps preserve the support arrangement for which the piping was designed.

Tightening hanger bolts “just to be safe” may seem sensible, but it can alter how the pipe is supported. Removing a hanger can shift load onto nearby supports. Adding insulation solely for the test can also change the weight being carried. Each of those changes may affect pipe position or support loading, and none is a routine requirement simply because a hydrostatic test is planned.

The goal isn’t to make every hanger immovable. It’s to test the pressure boundary while maintaining the designed support arrangement, subject to the approved test procedure and site requirements. That distinction is important: a spring can is meant to respond to movement, not to be turned into a rigid support without cause.

“No special preparation” doesn’t mean “no checks”

There’s a useful nuance here. Spring-can hangers generally require no special preparation for a hydrostatic test. That doesn’t mean the whole area can be ignored. The piping crew still follows the applicable test plan, drawings, safety rules, and inspection requirements.

Before pressurization, the work area may need a general visual review. Workers can confirm that supports are present, accessible, and not visibly damaged, and that the pipe is installed as required. They should also check that the test setup, isolation points, vents, drains, gauges, and temporary closures match the approved procedure. These are system-level checks, not special adjustments to spring-can hangers.

Some hanger designs include travel indicators, restraints, or temporary locking devices. In certain projects, an engineer or approved procedure may call for a specific setting or temporary measure during a test. If so, that direction takes priority. But it should come from the design documents or authorized test plan—not from an assumption that every spring can must be adjusted before pressure is applied.

That’s why careful communication matters. If a hanger looks out of position, or its condition is unclear, the crew should raise the issue with the responsible supervisor or engineering contact. Guessing at a setting can create an unintended load path. A quick clarification is usually far better than an improvised adjustment.

The weight of water deserves respect

Hydrostatic testing is often seen as safer than pneumatic testing because water stores less energy than compressed gas. Still, it isn’t risk-free. A filled pipe can impose substantial weight on its supports, and pressurized water can cause serious harm if a component fails.

That’s one reason the support system matters. The test plan should account for the condition of the piping, the weight of the test liquid, and the capacity of the supports. Depending on the system and project requirements, additional engineering review may be needed before testing. Spring-can hangers are part of that support picture, even though they don’t need routine adjustment just for the test.

It’s also worth remembering that hydrostatic testing and normal operation may involve different conditions. A cold water-filled line can load the supports differently from a hot operating line. The spring hanger’s intended role is to carry the pipe while allowing movement as conditions shift. Properly following the test plan helps ensure that the test doesn’t accidentally change the arrangement it is meant to evaluate.

Avoid adjustments that change the load path

A pipe support system works through a series of connected parts. If one support is removed or altered, the load may move elsewhere—sometimes in ways that aren’t obvious at a glance. A neighboring hanger, a structural attachment, or a section of pipe could take on more load than intended.

This is why casual adjustments are a poor substitute for a documented instruction. Tightening a bolt might seem minor, but it could affect a moving component or change the hanger’s behavior. Removing a spring can is more obvious, yet it can still shift load through the line. Even adding insulation for a test can affect weight if it changes the pipe’s condition from what the test plan assumes.

The same caution applies after the test. If a temporary restraint or other test-related device was installed under an approved procedure, it should be handled as directed. Workers shouldn’t leave temporary changes in place—or remove something that was meant to remain—without checking the relevant instructions.

A simple rule, backed by sound reasoning

For a pipe section with spring-can hangers, the usual approach before hydrostatic testing is straightforward: leave the hangers in their installed condition, with no special preparation. They support the pipe and allow movement; they don’t contain the pressure being tested.

That simple rule rests on practical engineering logic. Keep the pressure boundary intact, preserve the designed supports, account for the weight of the water, and follow the approved procedure. If a drawing or authorized instruction calls for a specific hanger measure, follow it. Otherwise, don’t tighten, remove, or alter spring-can hangers just because the piping is about to be hydrostatically tested.

In boiler work, small details can carry real weight—sometimes quite literally. Knowing what not to change is part of keeping a test safe, useful, and true to the system’s intended design.